• +91-85699-09696

Programmable Logic Controller Trainer Modular Application Modules Manufacturer,Supplier and Exporter in India

Programmable Logic Controller Trainer Modular Application Modules

Product Code : JA-DAIAPC-9612

These modular application modules connect quickly to the PLC trainers and give students programming challenges based on equipment that PLCs control. The set has six interchangeable modules, from motor start-stop and traffic lights to tank level control, object sorting and pneumatic cylinder sequencing. Each module adds a task to a trainer instead of replacing it.

Specifications of the PLC trainer application modules

Product codeJA-DAIAPC-9612
TypeApplication training modules for the PLC trainers; they add application tasks to a trainer rather than replace it
Modules in the setSix interchangeable modules: Motor/Conveyor Start-Stop, Forward/Reverse Interlock, Traffic Lights, Tank Level and Pump, Object Sorting with Photoelectric Sensor, and Pneumatic Cylinder Sequencing
PurposeProgramming challenges based on equipment that PLCs control
Connection to the PLC trainerKeyed patch connectors between each module and the trainer
Inputs and outputs24 V DC control inputs and outputs, each one labelled on the module
Display on each modulePrinted mimic diagram of the plant, with LEDs that show each output working
Mains loads and actuatorsSimulated in the basic set: mains loads and actuators such as motors, pumps and cylinders use simulation-only hardware
DocumentsOne exercise manual per module
ManufacturerJaincoLab, Ambala, India

Programming tasks with the PLC application modules

  • Connecting a module. Plug the keyed patch connectors of the module into the matching inputs and outputs of the Programmable Logic Controller Trainer. Check the 24 V DC common with the trainer switched off, then power up and test each output LED.
  • Forward and reverse interlock. On the Forward/Reverse Interlock module, write rungs so that the forward and reverse outputs can never be on together. Press reverse while forward is running and check that nothing changes until stop is pressed.
  • Larger projects. When a task needs more inputs and outputs than one trainer offers, drive the same module from the Industrial PLC System.
  • From model to machine. After the sorting module, give students the same task on the Conveyor System Trainer, where real sensors and a moving belt add timing problems.

Frequently Asked Questions

Which application module should students program first, and which should come last?
Start with the Motor/Conveyor Start-Stop and Traffic Lights modules, which teach latching, timers and counters with few inputs. Move on to Forward/Reverse Interlock and Tank Level and Pump. Leave Object Sorting and Pneumatic Cylinder Sequencing until students can plan a full sequence with sensor inputs.

Why must the forward and reverse outputs be interlocked in the PLC program?
On a real motor, the forward and reverse contactors closing together would short the supply. The program must block one output while the other is on, usually with a normally closed contact in each rung. Real panels add a hard-wired interlock as well, because software alone is not enough.

Why is a step sequence easier than interlocks when programming the cylinder sequencing module?
In a step sequence only one step is active at a time, and each step moves on when its condition is met. Extend, hold and retract then follow in a fixed order. With interlocks alone, every output needs conditions on all the others, and the program becomes hard to follow and to debug.

How many students can work on one PLC trainer and application module at a time?
Two students per trainer works well. One writes the program while the other wires and tests, and then they swap. A third student can record results, but larger groups leave students watching. Plan the module sets so each pair has its own task.

Which HS heading is usually used for PLC application modules made only for teaching?
Apparatus designed only for demonstration in teaching, and unsuitable for other uses, generally falls under HS heading 9023. Each country adds its own digits after the heading, so your customs broker confirms the full tariff line. Send the module list and quantities through our contact page.

Are the connecting cables and experiment manuals supplied with each set of modules?
Yes. Each module connects through keyed patch connectors and comes with its own exercise manual. Name the modules and the number of sets in your enquiry so each set is quoted complete. JaincoLab can also build extra modules to your own technical specification.

PLC trainers that take these modules

JaincoLab supports tender contractors as well as institutions: we manufacture and export laboratory equipment for Ministry of Education projects, World Bank-funded tenders and United Nations programmes, executed successfully in many countries, and we specialise in turnkey laboratory set-ups. Contact us through the tenders page early in your bid preparation.

See the Data Acquisition, Instrumentation and Process Control range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.

For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.

Last updated: 20 November 2026

   

Office Address

Jain Scientific Suppliers
2475-84, Hargolal Road,
Ambala Cantt, Haryana, India

[email protected]

+91-85699-09696

Follow Us