• +91-85699-09696

CB Transceiver Trainer Manufacturer,Supplier and Exporter in India

CB Transceiver Trainer

Product Code : JA-RATC-9590

The CB Transceiver Trainer teaches the operation, adjustment and repair of a 27 MHz AM/FM Citizens Band set. The transceiver sits in a training chassis with its key internal parts exposed and every control working. Test points, a 50 ohm dummy load, an attenuator and a power/SWR meter let students measure the transmitter on the bench.

Specifications of the CB transceiver trainer

Product codeJA-RATC-9590
TransceiverOne 27 MHz AM/FM Citizens Band transceiver; the exact destination-band version is named on the order
Channels40 channels, about 26.965 to 27.405 MHz, in the US-pattern teaching build*; other regional versions are separate configurations, built to order
RF outputUp to 4 W in the US-pattern build*
MountingTraining chassis with key internal parts exposed; all controls work as on a normal set
Test accessTest points for measurements without opening the case
Power supply13.8 V DC, fused
Bench RF kitCorrectly rated 50 ohm dummy load and attenuator*, power/SWR meter and shielded leads; RF measurements are made into the dummy load, not an antenna
AudioMicrophone and loudspeaker
DocumentationTeacher guide
ManufacturerJaincoLab, Ambala, India

* Standard JaincoLab specification for new builds.

Bench practicals on the CB transceiver trainer

  • Power into the dummy load. Connect the transmitter to the 50 ohm dummy load through the power/SWR meter and key it on a few channels. Record the forward power on each and check that the reflected reading stays close to zero.
  • Standing waves first. Study mismatch and standing waves on the Transmission Line Trainer, then return to the CB set and read its SWR into the matched load. Relate the low reading to what the line showed.
  • Channel frequencies. With the set keyed into the dummy load, take a sample through the attenuator and read it on the Frequency Counter. Never connect the counter straight to the transmitter output.
  • Antenna length. Use the Antenna System Demonstrator to see how a dipole's length sets its resonant frequency. Then work out the length of a quarter-wave whip for the CB band.

Frequently Asked Questions

How is the power/SWR meter connected and read on the trainer?
Place the meter in line between the transceiver and the 50 ohm load, using the shielded leads. Key the transmitter, read the forward power, then switch to the reflected or SWR scale. With the matched load the SWR should sit very close to one; a high reading points to a lead, connector or load fault.

Why are the lowest and highest channels checked when tuning a CB antenna?
An antenna is cut for one frequency, so its SWR rises towards the band edges. If the SWR is worse on the top channels, the antenna is too long. If it is worse on the bottom channels, it is too short. Adjust the length until both ends read about the same.

How does a CB transceiver produce its 40 channels from one crystal?
Most sets use a phase-locked loop. It compares a divided-down sample of the oscillator with a stable crystal reference and pulls the oscillator into step. Changing the divider ratio moves the oscillator by one channel, so the channel switch only has to set that ratio.

Why must students transmit into the 50 ohm dummy load and not an antenna?
The load turns the transmitter power into heat, so nothing is radiated and other radio users are not disturbed. It also gives a known, matched termination, which makes the power and SWR readings meaningful. Keep each transmission short so the load stays cool.

Do we need an import licence or type approval for the CB Transceiver Trainer?
Usually, yes. A CB set is a radio transmitter. Radio transmitters usually need an import licence or type approval in the buyer's country, and local CB rules set the channels and power. Check with your telecom regulator before ordering, and tell us the destination so the matching regional version is quoted.

Which documents should go with an import of CB trainers?
Keep the invoice and packing list together with the trainer's technical details: product code JA-RATC-9590, channel range, RF power and supply voltage. Regulators and customs often ask for these when they check a transmitter. Ask for the technical details when you request the quotation.

Other trainers in the radio and telephone range

JaincoLab specialises in turnkey laboratory projects funded by education ministries, the World Bank and United Nations programmes, manufacturing and exporting the equipment and executing these projects successfully in many countries. Tender bidders can send their requirement list through our tenders page for a line-by-line quotation.

See the Radio and Telephone Communications range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.

For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.

Last updated: 20 November 2026

   

Office Address

Jain Scientific Suppliers
2475-84, Hargolal Road,
Ambala Cantt, Haryana, India

[email protected]

+91-85699-09696

Follow Us