2 MHz Function Generator Manufacturer,Supplier and Exporter in India
Product Code : JA-SG-1546
The 2 MHz Function Generator is a bench signal source covering 0.1 Hz to 2 MHz. It gives sine, square, triangle, pulse and ramp waves from one analogue 50 ohm BNC output. It also has a TTL/CMOS sync output, an external VCF input and a four-digit frequency display.
Specifications of the 2 MHz function generator
| Product code | JA-SG-1546 |
|---|---|
| Frequency range | 0.1 Hz to 2 MHz |
| Waveforms | Sine, square and triangle; pulse and ramp with variable duty cycle |
| Main output | One analogue output on a 50 ohm BNC socket: up to 10 Vpp into 50 ohm, up to 20 Vpp into a high-impedance load |
| DC offset | Up to ±5 V into 50 ohm, within the amplitude headroom |
| Sync output | TTL/CMOS level |
| Frequency control | External VCF input; no internal AM, FM or automatic sweep on this model |
| Frequency display | Four-digit; the built-in counter reads 1 Hz to 30 MHz |
| Sine quality | Distortion below 1% from 10 Hz to 100 kHz; response within 0.5 dB from 0.1 Hz to 100 kHz |
| Power supply | 230 V AC, 50 Hz |
| Manufacturer | JaincoLab, Ambala, India |
Practicals with the 2 MHz function generator
- Square to triangle and back. Feed the square output into the Study of Operational Amplifier as Square to Triangular and Triangular to Square wave convertor board. Compare the op-amp triangle with the generator's own triangle. The same integrator and comparator pair works inside the generator.
- Filter response by hand. Set a sine of about 1 Vpp and step the frequency decade by decade into the Passive Filters board. Read input and output on the 30 MHz Oscilloscope, plot gain against frequency on log paper and mark the half-power point.
- Clocking a counter. Take the TTL/CMOS sync output to the clock input of the Study of 4 Bit Ripple Counter Forward and Reverse board. Start at a few hertz to watch the LEDs count, then raise the frequency and view the divided outputs on the scope.
- A manual sweep. Turn a variable DC voltage slowly at the VCF input and watch the display follow it. This shows voltage-controlled frequency at work, without an internal sweep circuit.
Frequently Asked Questions
How does an analogue function generator like this one produce triangle and square waves?
A constant current charges a capacitor, so its voltage rises in a straight line. A comparator reverses the current at set upper and lower levels, and the voltage falls again, giving the triangle. The comparator output itself switches between two levels, and that is the square wave.
What is the VCF input used for when the generator has no internal sweep?
The VCF input lets an outside voltage set the frequency. Inside, that voltage changes the current that charges the timing capacitor, so the frequency follows it. Feed a slow ramp from a second generator for a home-made sweep, or a steady DC level for remote tuning.
Is a 2 MHz function generator enough for a first-year electronics lab?
For most first-year work it is. RC filters, audio amplifiers, rectifier ripple, op-amp circuits and logic counters all run well below 2 MHz. Tuned RF circuits, IF stages and very fast pulse edges need more, so labs doing those choose a higher model from the signal generator range.
Can we test a sample generator before placing a bulk order?
Yes. A sample unit can be sent with the quotation. Your staff can then check the frequency range, output level and waveforms on your own bench before the main order. Ask for the sample when you send your enquiry through our contact page.
Which mains supply does the 2 MHz Function Generator need?
It runs on 230 V AC, 50 Hz single-phase mains. If your lab or your customers use a different mains voltage or plug type, mention it in your enquiry before you order.
Other generators in the signal generator range
- 5 MHz Function Generator
- 10 MHz Function Generator
- 13 MHz Function Generator
- 15 MHz Function Generator
- 2 to 5 MHz AM and FM Function Generator
- 150 MHz RF Signal Generator
See the Signal Generators range and more electronics lab equipment from JaincoLab, an electronics lab equipment manufacturer in India.
For a quotation, send the product name and the quantity you need through our contact page. For tender or project supply, see our tenders page.
